ABB OmniCore V250XT Product Manual Download | Manualshive

Page: 414 / 456

background image

8.4 Standard toolkit for controller

General

All service (repair, maintenance and installation) instructions contain lists of tools
required to perform the specified activity. All special tools, that is, all tools that are
not considered as standard tools as defined below, are listed in their instructions
respectively.

This way, the tools required are the sum of the standard toolkit and any tools listed
in the instructions.

Standard toolkit for controller

Description

Tool

Tx10

Screw driver, Torx

Tx20

Screw driver, Torx

Tx25

Screw driver, Torx

Tx25

Ball tipped screw driver, Torx

4 mm

Screw driver, flat blade

8 mm

Screw driver, flat blade

12 mm

Screw driver, flat blade

Phillips-1

Screw driver

8 mm

Box spanner

Toolkit recommended for troubleshooting

Note

Tool

Contents as specified above.

Normal shop tools

-

Multimeter

To document problems or procedures

Camera

414

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

8 Reference information

8.4 Standard toolkit for controller

«
...
412
413
414
415
416
...
»

Summary of Contents for OmniCore V250XT









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V250XT

Brand: adept technology Pages: 18

PROFI Dynamic XXL

Brand: fischertechnik Pages: 112

Brand: Kinova Pages: 148

Brand: neobotix Pages: 45

Brand: YASKAWA Pages: 88

Brand: XYZ Robot Pages: 55

Brand: e-Gizmo Pages: 59

Brand: Sony Pages: 120

Brand: XYZrobot Pages: 32

Brand: Bioloid Pages: 142

Brand: Schmalz Pages: 36

Brand: Slamtec Pages: 13

Brand: Slamtec Pages: 25

Brand: Neuromeka Pages: 325

Angle Armed Quad

Brand: Flybrix Pages: 41

Model Space Robi Pack 05

Brand: De Agostini Pages: 19

Brand: Brooks Pages: 232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands