ABB OmniCore V250XT Product Manual Download | Manualshive

Page: 103 / 456

background image

Conveyor tracking module (option)

For detail information on customer connections to conveyor tracking module, see

Application manual - Conveyor tracking

,

3HAC066561-001

.

xx2100002526

Customer cable layout

It is recommended to use multicore cable for the customer connection.

The cables connected by customer to the conveyor tracking module should go
through the cable grommet and fasten on the cabinet.

Note

The end user needs to install proper grommets according to the diameter of the
cables which need to go through the grommet.

Incorrect use of grommets will affect ingress protection, EMI/EMC and
temperature.

It is recommended to use

icotek

KT grommet.

The cable layout is recommended as the following illustration.

24V terminal block (option)

This connector is internally connected with the optional power supply. It is a 24 V
power supply for the customer. The characteristics are shown in the following
table.

Value

Parameter

24 V DC

Voltage

Continues on next page

Product manual - OmniCore V250XT

103

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

3 Installation and commissioning

3.5.8 Descriptions for connectors

Continued

«
...
101
102
103
104
105
...
»

Summary of Contents for OmniCore V250XT









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V250XT

Brand: Windoro Pages: 17

Brand: Robotics Pages: 31

Brand: ABB Pages: 19

Brand: artisan Pages: 15

Brand: SimLab Pages: 37

Brand: K-Team Pages: 44

Brand: VARRAM Pages: 30

Brand: Yujin Robot Pages: 39

FIFISH V6 Expert

Brand: QYSEA Pages: 40

Brand: Meccano Pages: 18

Brand: e-Gizmo Pages: 59

Brand: thomas and kosmos Pages: 8

Brand: Share Robotics Pages: 21

Moss Zombonitron 1600

Brand: Modular Robotics Pages: 24

Brand: EEVE Pages: 47

WaterColorBot v 2.0

Brand: Evil Mad Scientist Pages: 9

Brand: Evil Mad Scientist Pages: 12

Brand: Evil Mad Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands