ABB OmniCore V250XT Page 25 Product Manual Download | Manualshive

Page: 25 / 456

background image

The three-position enabling switch must be pressed to the center-position and the
hold-to-run button must be pressed to allow start of program execution, for example,
execute movement instructions.

In manual high speed, the initial speed of the movement, does not exceed 250
mm/s, that is limited to a percentage of the programmed speed. The speed can be
manually adjusted in steps up to the programmed speed.

When the three-position enabling device is released or fully compressed, the speed
is reset to the initial speed, that is, not exceeding 250 mm/s.

WARNING

Wherever possible, the manual mode of operation shall be performed with all
persons outside the safeguarded space.

Tasks normally performed in mode manual high speed

The following tasks are normally performed in manual high speed mode.

•

Program verification

•

Setting program pointer (to Main, to routine, to cursor, to service routine,
etc.)

•

Starting and stopping program execution

•

Stepping program execution

•

Manually adjusting speed (0–100%)

Product manual - OmniCore V250XT

25

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

1 Safety

1.4.1 About the manual mode

Continued

«
...
23
24
25
26
27
...
»

Summary of Contents for OmniCore V250XT









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V250XT

Brand: JAKA Pages: 73

Brand: Zimmer Pages: 16

Brand: fischertechnik Pages: 28

Brand: Barrett Pages: 13

Brand: Xtrem Bots Pages: 16

Brand: MAILLIS Pages: 140

SCARA YRC Series

Brand: Omron Pages: 44

Brand: Omron Pages: 54

Brand: Omron Pages: 62

TM Robot TM12 Series

Brand: Omron Pages: 82

Brand: Omron Pages: 140

Brand: Omron Pages: 149

SCARA R6Y XE Series

Brand: Omron Pages: 144

Brand: Omron Pages: 156

Brand: Omron Pages: 174

Brand: Omron Pages: 182

SCARA R6Y-XC Series

Brand: Omron Pages: 203

Brand: Omron Pages: 231

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands