ABB OmniCore V250XT Page 400 Product Manual Download

Page: 400 / 456

Significance

Description

The computer status LED indicates the startup progress of RobotWare
on the main computer.

Computer status,
PC STAT
(red/green)

Normal behavior:

Red, solid: Default when turning on the power.

Red, flashing: Initial self-test is ongoing and the operating system
is loading.

Green, even flashing (~1Hz): The operating system is loaded and
RobotWare is initializing.

Green, uneven flashing: The RobotWare system failed to load or
is not installed.

Green, solid: The computer is operational and the RobotWare
system is fully loaded.

If the LED does not turn steady green after approximately 5 minutes then
the LED can be used to identify the following issues:

•

No color: The internal power initialization failed. Restart the con-
troller. Replace the main computer if the problem remains.

•

Red, solid: Internal error. Restart the controller. Replace the main
computer if the problem remains.

•

Red, flashing continuously: Failed to load the operating system.
Restart the controller. See

Controller fails to start on page 369

Replace the main computer if the problem remains.

•

Green, even flashing continuously (~1Hz): Failure during start up.
Check error messages on FlexPendant. See

Controller fails to

start on page 369

•

Green, uneven flashing: RobotWare Installation Utilities mode.

Troubleshooting procedure

Note

Action

See

LEDs on page 399

If the LEDs do not turn steady after
approximately 5 minutes then re-
start the controller and check the
LEDs again.

Force start the RobotWare Installa-
tion Utilities mode, see

Controller

fails to start on page 369

Re-install RobotWare, if possible.

See

Replacing the main computer on page 226

The main computer may be faulty,
replace it and verify that the fault
has been fixed.

400

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

7 Troubleshooting

7.3.8 Troubleshooting the main computer

Continued

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands