Yealink VC110 Скачать руководство пользователя страница 123

Страница: 123 / 268

Configuring Call Preferences

111

This chapter provides information on how to configure endpoint‘s call preferences (e.g.,
call type and network bandwidth).

This chapter provides the following sections:



Configuring SIP Settings



Configuring H.323 Settings























Yealink VC110 video conferencing endpoint supports Session Initiation Protocol (SIP). If
your server supports SIP, you can use SIP to establish calls.

To establish calls using SIP, you can configure a SIP account for the endpoint.

SIP account parameters on the endpoint are described below:

Parameter

Description

Configuration Method

SIP Account

Enables or disables the SIP
account.

Default: Enabled

Remote Control

Web User Interface

Configures the user name of the
SIP account for register

Remote Control

Web User Interface

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды