Yealink VC110 Скачать руководство пользователя страница 216 | Manualshive

Страница: 216 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

204

Parameter

Description

Configuration Method

user to access the menus or log
into the web user interface.

Note: It can only be configured
when the user mode is enabled.
The endpoint supports ASCII
characters 32-126(0x20-0x7E) in
passwords. You can leave the
password blank.

To configure user mode via web user interface:

1.

Click on Security->Security.

2.

Select User from the pull-down list of User Type.

3.

Select Enabled from the pull-down list of User Mode.

4.

Configure a password or leave it blank in the User Password field.

5.

Click Confirm to accept the change.

The default enabled user type is administrator. Users can log into the web user interface
and access the ―Advanced‖ menu with administrator privilege by default. The default
administrator password is ―0000‖ and can be only changed by an administrator. For
security reasons, the administrator should change the default administrator password
as soon as possible. The endpoint supports ASCII characters 32-126(0x20-0x7E) in
passwords.

Administrator password parameters on the endpoint are described below:

Parameter

Description

Configuration Method

User Type

Specifies the user type.

Default: Administrator

Note: To configure a new
administrator password, you
need to select Administrator for
this parameter.

Web User Interface

«
...
214
215
216
217
218
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Yealink Страницы: 8

Бренд: Hall Technologies Страницы: 10

Бренд: Polyaire Страницы: 20

Бренд: Coby Страницы: 3

MFIT MERCEDES SPRINTER W907 EVO 2

Бренд: Audio System Страницы: 2

Бренд: Danfoss Страницы: 44

Бренд: Greenheck Страницы: 16

Бренд: AMS Страницы: 14

Бренд: VADDIO Страницы: 40

Бренд: U-Prox Страницы: 3

Бренд: Samsung Страницы: 18

Бренд: Samsung Страницы: 23

Бренд: Sanyo Страницы: 4

Бренд: Sanyo Страницы: 13

Бренд: Sanyo Страницы: 13

Бренд: Sanyo Страницы: 13

Бренд: Sanyo Страницы: 15

OneCell RP Series

Бренд: CommScope Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды