Yealink VC110 Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

146

Parameter

Description

Configuration Method

phone.

Default: English

To specify the language for the web user interface via web user interface:

1.

Click Language at the top of the web page.

2.

Select the desired language from the pull-down list of Language.

To specify the language for the display device and the video conferencing phone via
the remote control:

1.

Select Menu->Basic.

2.

Select the desired language from the pull-down list of Language.

3.

Press the Save soft key to accept the change.

Time and date are displayed on the idle screen of the display device and the video
conferencing phone. Time and date are synced automatically from the NTP server by
default. The default NTP server is cn.pool.ntp.org. The NTP server is configurable
manually or obtained by DHCP via DHCP Option 42. The phone will use the NTP server
obtained by DHCP preferentially. If the endpoint cannot obtain the time and date from
the NTP server, you need to manually configure them. The time and date can use one of
several different formats.

Time Zone

A time zone is a region on Earth that has a uniform standard time. It is convenient for
areas in close commercial or other communication to keep the same time. When
configuring the endpoint to obtain the time and date from the NTP server, you must set
the time zone.

«
...
156
157
158
159
160
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Caliber Страницы: 18

Бренд: Jensen Страницы: 3

ONECONCEPT 10029361

Бренд: Chal-tec Страницы: 29

Бренд: Ubiquiti Страницы: 42

Бренд: Lenze Страницы: 76

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 43

Бренд: Kenwood Страницы: 26

Бренд: Kenwood Страницы: 22

Бренд: Kenwood Страницы: 43

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 26

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 52

Бренд: Kenwood Страницы: 35

Бренд: Kenwood Страницы: 44

Бренд: Kenwood Страницы: 80

Бренд: Kenwood Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды