Yealink VC110 Скачать руководство пользователя страница 178

Страница: 178 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

166

The MTU parameter on the endpoint is described below.

Parameter

Description

Configuration Method

Video MTU

Specifies the maximum MTU size
(in bytes) of video packets sent
by the endpoint.

Valid Values: Integer from 1000 to
1500

Default: 1500

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

To configure MTU via web user interface:

Click on Network->Advanced.

In the MTU block, enter the desired value in the Video MTU field.

Click Confirm to accept the change.

A dialog box pops up to prompt that the settings will take effect after a reboot.

Click Confirm to reboot the endpoint immediately.

To configure MTU via the remote control:

Select Menu->Advanced (default password: 0000) ->Advanced Network.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды