Yealink VC110 Скачать руководство пользователя страница 107

Страница: 107 / 268

Configuring Network

STUN feature parameters on the endpoint are described below:

Parameter

Description

Configuration Method

Active

Enables or disables the STUN
(Simple Traversal of UDP over
NATs) feature on the endpoint.

Default: Disabled

Remote Control

Web User Interface

STUN Server

Configures the IP address or the
domain name of the STUN
(Simple Traversal of UDP over
NATs) server.

Default: Blank

Remote Control

Web User Interface

STUN Port

Configures the port of the STUN
(Simple Traversal of UDP over
NATs) server.

Default: 3478

Remote Control

Web User Interface

NAT_Traversal

Configures the NAT traversal
type. You can configure it for the
SIP account or SIP IP call
separately.



Disabled



STUN



StaticNat

Default: Disabled

Note: STUN works only if this
parameter is set to STUN.

Web User Interface

To configure STUN server via web user interface:

Click on Network->NAT/Firewall.

In the Stun Config block, select the desired value from the pull-down list of Active.

Enter the IP address or the domain name of the STUN server in the STUN Server
field.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды