Yealink VC110 Скачать руководство пользователя страница 101

Страница: 101 / 268

Configuring Network

Parameter

Description

Configuration Method

the configured ports.

If you change this parameter, the
endpoint will reboot to make the
change take effect.

To configure reserved ports via web user interface:

Click on Network->NAT/Firewall.

In the Reserve Port block, configure the UDP port range in the UDP Port Scope field.

In the Reserve Port block, configure the TCP port range in the TCP Port Scope field.

Click Confirm to accept the change.

A dialog box pops up to prompt that the settings will be implemented after a
reboot.

Click Confirm to reboot the endpoint immediately.

To configure reserved ports via the remote control:

Select Menu->Advanced (default password: 0000) ->NAT/Firewall.

In the Reserved block, configure the range of the UDP ports and TCP ports.

Press the Save soft key to accept the change.

The display device prompts ―Reboot now?‖.

Select OK to reboot the endpoint immediately.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды