Yealink VC110 Скачать руководство пользователя страница 103

Страница: 103 / 268

Configuring Network

Parameter

Description

Configuration Method

does not use the NAT
feature.



Manual—the endpoint uses
the manually configured
NAT public address.



Auto—the endpoint obtains
the NAT public address from
the Yealink-supplied server.

Default: Disabled

NAT Public IP

Address



Displays the NAT public
address automatically
obtained from the
Yealink-supplied server if
the static NAT is set to Auto.



Configures the NAT public
address for the endpoint if
the static NAT is set to
Manual.

Remote Control

Web User Interface

Route Traversal

Configures the route traversal
type.



Auto—NAT works only when
making a call to public
network or receiving a call
from the public network.



Compulsory—NAT works
when you are in multi-level
intranet network to solve the
one-way audio or video
problem.

Default: Auto

Web User Interface

NAT_Traversal

Configures the NAT traversal
type. You can configure it for the
SIP account or SIP IP call
separately.



Disabled



STUN



StaticNat

Web User Interface

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды