Yealink VC110 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 268

background image

Configuring Network

75

3.

Enter the desired time interval in the Packet Interval (1-3600s) field.

4.

Click Confirm to accept the change.

A dialog box pops up to prompt that the settings will take effect after a reboot.

5.

Click Confirm to reboot the endpoint immediately.

To configure LLDP via the remote control:

1.

Select Menu->Advanced (default password: 0000) ->Advanced Network.

2.

In the LLDP block, check the Active checkbox.

3.

Enter the desired value in the Packet Interval (1-3600s) field.

4.

Press the Save soft key to accept the change.

The display device prompts ―Reboot now?‖.

5.

Select OK to reboot the endpoint immediately.

VLAN is disabled on endpoints by default. You can configure VLAN manually. Before
configuring VLAN on the endpoints, you need to obtain the VLAN ID from your network
administrator.

Parameters of manual VLAN on the endpoint are described below.

Parameter

Description

Configuration Method

Internet

Port->Active

Enables or disables VLAN for the
Internet (WAN) port.

Default: Disabled

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

«
...
85
86
87
88
89
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

SAE 07.2 Series

Бренд: AUMA Страницы: 116

kb sound Series

Бренд: EIS Страницы: 2

Бренд: eMoMo Страницы: 2

Бренд: Zonex Страницы: 28

Бренд: FOUR Страницы: 28

Бренд: Kraken Acoustics Страницы: 12

AT-UHD-HDVS-300-KIT

Бренд: Atlona Страницы: 50

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 20

Бренд: RCA Страницы: 1

Бренд: GE Страницы: 96

Бренд: JVC KENWOOD Страницы: 110

3-293-639-11(1)

Бренд: Sony Страницы: 36

3-287-077-14(2)

Бренд: Sony Страницы: 48

3-097-196-14(1)

Бренд: Sony Страницы: 243

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды