Yealink VC110 Скачать руководство пользователя страница 258

Страница: 258 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

246

have the same effect as a static image.



Configure the automatic sleep time to be 1 hours or less.



Consider decreasing the monitor‘s sharpness, brightness, and contrast settings if
they are set to their maximum values.

When you do one of the following, the endpoint will reboot:



Reboot endpoint



Reset endpoint



Upgrade firmware



Configure some features need to take effect after a reboot

You can reboot the endpoint in the following ways:



Select Menu->Advanced (default password: 0000) ->Reboot & Reset->Reboot,
and then press .



Log into web user interface and click on Setting->Upgrade->Reboot, and then
click Confirm.



Ensure that the firmware is different from the firmware currently in use.



Ensure that the downloaded firmware applies to the endpoint.



Ensure that the endpoint is powered on normally, and the network is available
during the upgrade process.



When upgrading firmware via web user interface, ensure that the web user
interface is not refreshed or closed during the upgrade process.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды