Yealink VC110 Скачать руководство пользователя страница 88

Страница: 88 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

Parameter

Description

Configuration Method

VID(1-4094)

Configures VLAN ID for the
Internet (WAN) port.

Default: 1

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

Priority

Configures VLAN priority for the
Internet (WAN) port.

Valid values: 0-7

7 is the highest priority, 0 is the
lowest priority.

Default: 0

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

To configure VLAN for Internet port via web user interface:

Click on Network->Advanced.

In the VLAN block, select the desired value from the pull-down list of Internet Port
Active.

Enter the VLAN ID in the VID (1-4094) field.

Select the desired value (0-7) from the pull-down list of Priority.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды