Yealink VC110 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

10

Infrared Sensor

The infrared sensor is located within the Yealink logo. Aim the remote control at the
camera IR sensor to operate the unit.

Note

The right side of the VC110 all-in-one unit

Port Name

Description

①

USB

Inserts a USB flash drive to one of the two USB ports
for storing screenshots and recording videos.
Inserts a dongle to one of the two USB ports for
connecting the VCM60 video conferencing wireless
microphone.

Note:



The wireless microphone dongle and USB flash
drive can work at the same time.



If two USB flash drives are connected, only the
latter one can be identified.

When the endpoint is powered on, avoid physically turning the camera. This may cause
permanent damage to the camera. Always use the remote control to pan and tilt it.

«
...
20
21
22
23
24
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: EAW Страницы: 9

MME100 - Audio Micro System

Бренд: Magnavox Страницы: 23

Бренд: Panasonic Страницы: 16

SB3.0-1SP-US-40

Бренд: SMA Страницы: 17

Бренд: J&M Corporation Страницы: 9

Бренд: Clas Ohlson Страницы: 36

Бренд: Ubiquiti Страницы: 42

Бренд: AbleNet Страницы: 8

Бренд: LENCO Страницы: 24

Бренд: Toa Страницы: 9

C51 COMMUNICATION SYSTEM-SD7505

Бренд: Motorola Страницы: 90

Бренд: Samsung Страницы: 11

SoundTower TW-H5500

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 34

Бренд: Caliber Страницы: 4

Бренд: Caliber Страницы: 28

Бренд: THOMSON Страницы: 68

Бренд: Seat Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды