Yealink VC110 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 268

background image

Configuring Network

97

3.

Click Confirm to accept the change.

To configure STUN for SIP IP call via web user interface:

1.

Click on Account->SIP IP Call.

2.

Select STUN from the pull-down list of NAT_Traversal.

3.

Click Confirm to accept the change.

To configure STUN server via the remote control:

1.

Select Menu->Advanced (default password: 0000) ->NAT/Firewall.

Mark the ON radio box in the STUN Active field.

2.

Enter the IP address or the domain name of the STUN server in the STUN Server
field.

3.

Enter the port of the STUN server in the Port field.

4.

Press the Save soft key to accept the change.

To configure STUN server for SIP IP call via the remote control:

1.

Select Menu->Advanced (default password: 0000) ->SIP IP Call.

2.

Select STUN from the pull-down list of NAT_Traversal.

3.

Press the Save soft key to accept the change.

Full Cone:

A full cone NAT is one where all requests from the same internal IP address and port are
mapped to the same external IP address and port. Furthermore, any external host can
send a packet to the internal host, by sending a packet to the mapped external
address.

«
...
107
108
109
110
111
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Handicare Страницы: 56

Бренд: Barco Страницы: 158

Бренд: HIMA Страницы: 42

Бренд: Teac Страницы: 23

Бренд: Bame Страницы: 12

Cruisair SMX II

Бренд: Taylor Made Environmental Страницы: 36

Бренд: Denver Страницы: 12

Бренд: ISOUND Страницы: 28

Бренд: DriSteem Страницы: 4

SmartShop Maker

Бренд: Laguna Tools Страницы: 70

Бренд: RCA Страницы: 68

Stealthbox SB-CAN-G2MVX3D/10TW3

Бренд: JL Audio Страницы: 6

Бренд: GE Страницы: 79

Бренд: Roger Страницы: 2

Бренд: Rohde & Schwarz Страницы: 327

Бренд: Dynavin Страницы: 44

Бренд: Krüger & Matz Страницы: 47

Бренд: JBL Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды