Yealink VC110 Скачать руководство пользователя страница 223

Страница: 223 / 268

Configuring Security Features

211

Parameter

Description

Configuration Method

trusted certificates list. Only when
the authentication succeeds, will
the endpoint trust the server.

If you change this parameter, the
endpoint will reboot to make the
change take effect.

Common Name

Validation

Enables or disables the endpoint
to mandatorily validate the
CommonName or
SubjectAltName of the certificate
sent by the server.

Default: Disabled

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Web User Interface

CA Certificates

Configures the type of certificates
in the Trusted Certificates list for
the endpoint to authenticate for
the TLS connection.



Default Certificates



Custom Certificates



All Certificates

Default: Default Certificates

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Web User Interface

Upload Trusted

Certificate File

Upload the custom CA certificate
to the endpoint.

Note: A maximum of 10 CA
certificates can be uploaded to
the endpoint. The certificate you
want to upload must be in *.pem,
*.crt, *.cer or *.der format.

Web User Interface

Device

Certificates

Upload the customized CA
certificate to the endpoint.



Default Certificates

Web User Interface

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды