Yealink VC110 Скачать руководство пользователя страница 72

Страница: 72 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

Parameter

Description

Configuration Method

the "Static IPv4 DNS" is set to On.
If you change this parameter, the
endpoint will reboot to make the
change take effect.

To configure static DNS address when DHCP is used via web user interface:

Click on Network->LAN Configuration.

In the IPv4 Config block, mark the DHCP radio box.

In the Static DNS block, mark the On radio box.

Enter the desired values in the Primary DNS and Secondary DNS fields.

Click Confirm to accept the change.

A dialog box pops up to prompt that settings will take effect after a reboot.

Click Confirm to reboot the phone.

To configure static DNS when DHCP is used via the remote control:

Select Menu->Advanced (default password: 0000) ->LAN Configuration->IPv4.

Check the DHCP checkbox.

Check the Static DNS checkbox.

Enter the desired values in the DNS Primary Server and DNS Secondary Server
fields respectively.

Press the Save soft key to accept the change.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды