Yealink VC110 Скачать руководство пользователя страница 79

Страница: 79 / 268

Configuring Network

Parameter

Description

Configuration Method

reboot to make the change take
effect.

Static DNS/Static

IPv6 DNS

Triggers the static IPv6 DNS
feature to on or off.

Default: Off

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

DNS Primary

Server/Primary

DNS

Configures the primary IPv6 DNS
server.

Default: Blank

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

DNS Secondary

Server/Secondary

DNS

Configures the secondary IPv6
DNS server.

Default: Blank

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

To configure IPv6 address assignment method via web user interface:

Click on Network->LAN Configuration.

Select the desired IP mode (IPv6 or IPv4 & IPv6) from the pull-down list of IPv4/IPv6.

In the IPv6 Config block, mark the DHCP or the Static IP radio box.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды