Yealink VC110 Скачать руководство пользователя страница 171

Страница: 171 / 268

Configuring Endpoint Settings

159

Parameter

Description

Configuration Method

volume is set to 0: ) during
a call.



Disabled- the endpoint does
not display output mute icon
during a call.



Hide with UI- the endpoint
displays output mute icon
during a call, but the output
mute icon will hide with UI.



Enabled- the endpoint
displays output mute icon
during a call.

Default: Disabled

Gazeat Icon

Enables or disables the endpoint
to hide gazeat icon ( )
during a call.



Disabled- the endpoint does
not display gazeat icon
during a call.



Hide with UI- the endpoint
displays gazeat icon during
a call, but the gazeat icon
will hide with UI.



Enabled- the endpoint
displays gazeat icon during
a call.

Default: Disabled

Web User Interface

To enable the hiding icons in a call feature via web user interface:

Click on Setting->General.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды