Yealink VC110 Скачать руководство пользователя страница 124

Страница: 124 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

112

Parameter

Description

Configuration Method

authentication.

Default: Blank

User Name

Specifies the user name to use for
authentication when registering
with a SIP server.

Default: Blank

Remote Control

Web User Interface

Password

Specifies the password
associated with the user name
used to authenticate the
endpoint to the SIP server.

Default: Blank

Remote Control

Web User Interface

Server Host

Configures the IP address or
domain name of the SIP server
for the SIP account.

Default: Blank

Remote Control

Web User Interface

Enable Outbound

Proxy Server

Enables or disables the endpoint
to send requests of the SIP
account to the outbound proxy
server.

Default: Disabled

Remote Control

Web User Interface

Outbound Proxy

Server

Configures the IP address or
domain name of the outbound
proxy server for the SIP account.

Valid values: Integer from 1 to
65535.

Default: it is configurable only
when the Outbound Proxy Server
is enabled.

Remote Control

Web User Interface

Transport

Configures the type of transport
protocol for the SIP account.



UDP—provides best-effort
transport via UDP for SIP
signaling.



TCP—provides reliable
transport via TCP for SIP
signaling.



TLS—provides secure
communication of SIP

Remote Control

Web User Interface

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды