Yealink VC110 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 268

background image

Configuring Network

77

5.

Click Confirm to accept the change.

A dialog box pops up to prompt that the settings will take effect after a reboot.

6.

Click OK to reboot the phone.

To configure VLAN via the remote control:

1.

Select Menu->Advanced (default password: 0000) ->Advanced Network.

2.

In the VLAN block, check the Active checkbox.

3.

Enter the VLAN ID in the VID(1-4094) field.

4.

Enter the priority value (0-7) in the Priority field.

5.

Press the Save soft key to accept the change.

The display device prompts ―Reboot now?‖.

6.

Select OK to reboot the endpoint immediately.

The endpoint supports VLAN discovery via DHCP. When the VLAN Discovery method is
set to DHCP, the endpoint will examine the DHCP option for a valid VLAN ID. The
predefined option 132 is used to supply the VLAN ID by default. You can customize the
DHCP option used to request the VLAN ID.

Parameters of VLAN feature on the endpoint are described below.

Parameter

Description

Configuration Method

DHCP

VLAN

->

Active

Enables or disables the DHCP
VLAN discovery feature on the
endpoint.

Default: Enabled

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Web User Interface

Option

Configures the DHCP option from
which the endpoint obtains the
VLAN settings.

You can configure at most five
DHCP options and separate them
by commas.

Valid Values: 128-254

Default: 132

Note: If you change this
parameter, the endpoint will

Web User Interface

«
...
87
88
89
90
91
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Xantech Страницы: 102

Бренд: Radionics Страницы: 14

Бренд: auna multimedia Страницы: 124

Бренд: Metra Electronics Страницы: 12

Бренд: StarLeaf Страницы: 2

GrowControl GCX

Бренд: Agrowtek Страницы: 78

Бренд: DAPAudio Страницы: 17

Clementine 8440

Бренд: PNI Страницы: 8

Бренд: Iluv Страницы: 40

Бренд: Boss Audio Systems Страницы: 1

Бренд: JVC Страницы: 56

Бренд: JVC Страницы: 41

Бренд: JVC Страницы: 48

Бренд: JVC Страницы: 74

Бренд: JVC Страницы: 28

Бренд: JVC Страницы: 82

Бренд: JVC Страницы: 31

Бренд: JVC Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды