Yealink VC110 Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

192

It will prevent importing the title of the contact information which is located in the
first line of the CSV file.

6.

(Optional.) Check the Delete Old Contacts checkbox.

It will delete all existing contacts while importing the contact list.

7.

Select the desired value from the pull-down list.

-

If Ignore is selected, this column will not be imported to the endpoint.

-

If Display Name is selected, this column will be imported to the endpoint as the
contacts‘ name.

-

If number1/2/3 is selected, this column will be imported to the endpoint as the
contacts‘ number.

8.

Click Confirm to complete importing the contact list.

The web user interface prompts "Contacts imported successfully!".

To export a XML/CSV file of the contact list via web user interface:

1.

Click on Directory->Local Directory.

2.

Click Import/Export, and select Export XML or Export CSV.

3.

The contact list is saved to your local endpoint.

LDAP (Lightweight Directory Access Protocol) is an application protocol for accessing
and maintaining information services for the distributed directory over an IP network.
Yealink VC110 endpoint

is configurable to interface with a corporate directory server

that supports LDAP version 2 or 3. The following LDAP servers are supported:

«
...
202
203
204
205
206
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Data I/O Страницы: 88

Бренд: AddPac Страницы: 269

Бренд: ATEN Страницы: 176

Бренд: JBL Страницы: 11

Бренд: Polycom Страницы: 2

HDX Desktop Systems

Бренд: Polycom Страницы: 2

Бренд: Hyundai Страницы: 61

Compact FLASH III

Бренд: ACS Страницы: 37

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 21

Бренд: Bosch Страницы: 498

VoiceSonic KX-NT700

Бренд: Panasonic Страницы: 80

Бренд: Lexicomm Страницы: 24

Бренд: Pioneer Страницы: 4

Бренд: Pioneer Страницы: 8

Бренд: Pioneer Страницы: 4

Бренд: Pioneer Страницы: 17

Бренд: Pioneer Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды