Yealink VC110 Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

156

3.

Click Confirm to accept the change.

To configure the key tone via the remote control:

1.

Select Menu->Basic.

2.

Mark the radio box in the Key Tone field.

3.

Press the Save soft key to accept the change.

During a call, the endpoint will display some information and icons (such as call time,
mute icon and recording icon) by default, you can know the call status from these
information and icons. You can also hide these icons as needed to achieve the best
video effects.

Parameters of hiding icons in a call feature on the endpoint are described below:

Parameter

Description

Configuration Method

Time Icon

Enables or disables the endpoint
to hide call time during a call.



Disabled- the endpoint does
not display call time during
a call.



Hide with UI- the endpoint
displays call time during a
call, but the call time will
hide with UI.



Enabled- the endpoint
displays call time during a
call.

Default: Hide with UI

Web User Interface

Mute Icon

Enables or disables the endpoint
to hide mute icon ( ) during
a call.



Disabled- the endpoint does
not display mute icon during
a call.



Hide with UI- the endpoint
displays mute icon during a
call, but the mute icon will
hide with UI.



Enabled- the endpoint

Web User Interface

«
...
166
167
168
169
170
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

SC600 Marcopolo

Бренд: Valeo Страницы: 12

SoundPoint Pro SE-220

Бренд: Polycom Страницы: 2

Videoconference System

Бренд: TANDBERG Страницы: 10

Бренд: HEIDENHAIN Страницы: 64

Бренд: Siku Страницы: 150

Бренд: FAAC Страницы: 16

Бренд: N-Com Страницы: 12

Бренд: Regintech Страницы: 82

Stealthbox SB-HY-VELOSTR/10TW3

Бренд: JL Audio Страницы: 7

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 20

E84DGFCp Series

Бренд: Lenze Страницы: 100

Бренд: Boss Audio Systems Страницы: 1

Бренд: Pioneer Страницы: 80

Бренд: Pioneer Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды