Yealink VC110 Скачать руководство пользователя страница 187 | Manualshive

Страница: 187 / 268

background image

Configuring Endpoint Settings

175

To configure camera settings via the remote control:

1.

Select Menu->Video & Audio->Camera General Settings.

2.

Configure the camera settings.

3.

Press the Save soft key to accept the change.

Local video is displayed on the display device of the far site during a call. For the best
view, you can enable the Far Control of Near Camera feature to allow the far site to
control the focus and angle of the local camera. You can also specify whether the far
site is allowed to store and use the local camera presets.

Far control of the near camera parameters are described below.

Parameter

Description

Configuration Method

Not FECC in

call(0~300s)

Configures the duration time (in
seconds) when far site cannot
control the local camera during a
call.

Default: 15

If it is set to 15, the far site is not
allowed to control the local
camera in the first 15 seconds of
the call.

Web User Interface

Far Control Near

Camera

Enables or disables the far site to
control the near site camera.

Default: Enabled

Remote Control

Web User Interface

Far Set of Camera

Presets

Enables or disables the far site to
store the camera presets.

Default: Disabled

Remote Control

Web User Interface

Far Move to

Camera Presets

Enables or disables the far site to
use the camera presets.

Default: Disabled

Remote Control

Web User Interface

To configure far-end camera control via web user interface:

1.

Click on Setting->Video & Audio.

2.

Enter the desired time in the Not FECC in call(0~300s) field.

3.

Select the desired values from the pull-down lists of Far Control Near Camera.

4.

Select the desired values from the pull-down lists of Far Set of Camera Presets.

«
...
185
186
187
188
189
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Panasonic Страницы: 28

Бренд: GRAUPNER Страницы: 180

Бренд: Beyerdynamic Страницы: 112

Бренд: SONIQ Страницы: 7

Бренд: Discount Car Stereo Страницы: 9

Бренд: HME Страницы: 2

Бренд: Grandstream Networks Страницы: 20

RealPresence Utility Cart 500

Бренд: Polycom Страницы: 10

Бренд: Schake Страницы: 2

Бренд: Panasonic Страницы: 100

SmartShop Maker

Бренд: Laguna Tools Страницы: 70

Бренд: Basler Страницы: 12

Бренд: Iluv Страницы: 36

Stealthbox SB-F-150-SPRCRW/13TW5v2

Бренд: JL Audio Страницы: 5

Бренд: Boss Audio Systems Страницы: 13

Бренд: Boss Audio Systems Страницы: 36

Бренд: Kenwood Страницы: 2

Бренд: Kenwood Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды