Yealink VC110 Скачать руководство пользователя страница 85

Страница: 85 / 268

Configuring Network

TLV Type

TLV Name

Description

System Description

Description of the endpoint.

Description includes firmware version of
the endpoint.

System Capabilities

The supported and enabled endpoint
capabilities.

The Telephone capability is supported
and enabled by default.

Port Description

Description of port that sends data unit.

The default value is ―WAN PORT‖.

IEEE Std 802.3

Organizationally

Specific TLV

MAC/PHY
Configuration/Status

Duplex mode and network speed
settings of the endpoint.

The Auto Negotiation is supported and
enabled by default.

The advertised capabilities of PMD.

Auto-Negotiation is:

100BASE-TX (full duplex mode)

100BASE-TX (half duplex mode)

10BASE-T (full duplex mode)

10BASE-T (half duplex mode)

TIA

Organizationally

Specific TLVs

Media Capabilities

The MED device type of the endpoint and
the supported LLDP-MED TLV type can be
encapsulated in LLDPDU.

The supported LLDP-MED TLV types are:
LLDP-MED Capabilities, Network Policy,
Extended Power via MDI-PD, Inventory.

Network Policy

Port VLAN ID, application type, L2 priority
and DSCP value.

Extended
Power-via-MDI

Power type, source, priority and value.

Inventory –
Hardware Revision

Hardware revision of the endpoint.

Inventory –
Firmware Revision

Firmware revision of the endpoint.

Inventory –
Software Revision

Software revision of the endpoint.

Inventory – Serial

Serial number of the endpoint.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды