Yealink VC110 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

134

To configure history record via web user interface:

1.

Click on Setting->Call Features.

2.

Select the desired value from the pull-down list of History Record.

3.

Click Confirm to accept the change.

To configure history record via the remote control:

1.

Select Menu->Call Features.

2.

Check the History Record checkbox.

3.

Press the Save soft key to accept the change.

The endpoint automatically detects the available bandwidth for call connection by
default. The VC110 supports connecting to other devices with different bandwidth. If a
device with lower bandwidth joins a call, the video quality will stay the same or will not
reduce a lot. You can specify the uplink and downlink bandwidths for the endpoint to
achieve the best result. Uplink bandwidth is the max bandwidth of outgoing calls. And
downlink bandwidth is the max bandwidth of incoming calls. The configurable
bandwidths on the endpoint are: 256 kb/s, 384 kb/s, 512 kb/s, 640 kb/s, 768 kb/s, 1024
kb/s, 1280 kb/s, 1500 kb/s, 2000 kb/s, 3000 kb/s, 4000 kb/s. The specified value of the
uplink bandwidth becomes the maximum value that users can select from the pull-down
list of Bandwidth in the dial screen.

Note

The actual resolution depends on the performance of the far site, and is affected by the

quality of the communication channel.

«
...
144
145
146
147
148
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

ProducTVity Station

Бренд: red lion Страницы: 8

Бренд: VIS-A-VIS Страницы: 4

Бренд: Avaya Страницы: 5

COLLABORATE Room

Бренд: ClearOne Страницы: 48

Бренд: Schake Страницы: 2

Talk-N-Trace TM-110

Бренд: JDS Uniphase Страницы: 20

Бренд: Samsung Страницы: 69

Бренд: BRONKHORST Страницы: 33

Бренд: Alpine Страницы: 184

Бренд: Sanyo Страницы: 19

Бренд: Aastra Страницы: 101

Бренд: Supra Страницы: 80

Бренд: Generex Страницы: 166

Бренд: Durablow Страницы: 12

Бренд: Avipas Страницы: 48

Бренд: Fostex Страницы: 24

Бренд: Q Acoustics Страницы: 32

Бренд: RCA Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды