Yealink VC110 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 268

background image

Configuring Call Preferences

129

2.

Select the desired value from the pull-down list of Call Protocol.

3.

Click Confirm to accept the change.

To configure call protocol via the remote control:

1.

Select Menu->Call Features ->Call Protocol.

2.

Select the desired value from the pull-down list of Call Protocol.

3.

Press the Save soft key to accept the change.

Do not Disturb allows the endpoint to reject all incoming calls automatically. You can
activate the DND mode for the endpoint when it is idle, and the DND mode will be
deactivated after the endpoint places a call. You can also activate the DND mode for
the endpoint during a call, and the DND mode will be deactivated after the endpoint
ends the call.

The DND parameter on the endpoint is described below:

Parameter

Description

Configuration Method

DND

Enables or disables DND mode
on the endpoint.

Default: Disabled

Remote Control

Web User Interface

To configure DND via web user interface:

1.

Click on Setting->Call Features.

«
...
139
140
141
142
143
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: Jensen Страницы: 4

Бренд: Blaupunkt Страницы: 15

TesiraFORTÉ AVB VT4

Бренд: Biamp Страницы: 2

Бренд: J&M Страницы: 8

Бренд: Jensen Audio Страницы: 20

Бренд: SALUPO Страницы: 22

Soundpoint IP 301

Бренд: Polycom Страницы: 4

Бренд: Taiden Страницы: 19

Бренд: Waversasystems Страницы: 24

Бренд: Qtx Страницы: 5

CONFERENCE MAX NDA-31109

Бренд: NEC Страницы: 5

Бренд: Dell Страницы: 67

Бренд: Noblex Страницы: 13

Бренд: Philips Страницы: 16

Бренд: Philips Страницы: 76

Бренд: BMPRO Страницы: 32

Бренд: Talkaphone Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды