Yealink VC110 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 268

background image

Configuring Call Preferences

133

To configure call match via web user interface:

1.

Click on Setting->Call Features.

2.

Select the desired value from the pull-down list of Call Match.

3.

Click Confirm to accept the change.

To configure call match via the remote control:

1.

Select Menu->Call Features.

2.

Check the Call Match checkbox.

3.

Press the Save soft key to accept the change.

The endpoint maintains a local call history, which contains call information such as
remote party identification, time and date, and call duration (call duration is only listed
on the web user interface). Users can manage call history list via the remote control,
web user interface and video conferencing phone. To save call history, you must enable
the history record feature on the endpoint in advance. If history record feature is
disabled, the endpoint will not save call log and prompt the missed call.

The history record parameter on the endpoint is described below:

Parameter

Description

Configuration Method

History Record

Enables or disables the history
record feature on the endpoint.

Default: Enabled

Remote Control

Web User Interface

«
...
143
144
145
146
147
...
»

Содержание VC110













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VC110

Бренд: Panasonic Страницы: 45

Бренд: Nakamichi Страницы: 12

Бренд: Teac Страницы: 16

Zonemaster ZoneTouch V2

Бренд: Polyaire Страницы: 24

Бренд: SKF Страницы: 63

Бренд: vistaCNC Страницы: 7

Бренд: 2VV Страницы: 19

Бренд: 2VV Страницы: 24

MEISTERSTUCK SO-610

Бренд: Sonoro Страницы: 334

Бренд: Craig Страницы: 2

Бренд: Basler Страницы: 12

Бренд: Sharp Страницы: 18

Бренд: Pioneer Страницы: 8

Бренд: Pioneer Страницы: 64

Бренд: Pioneer Страницы: 64

Бренд: Techno CNC Systems Страницы: 67

Бренд: Technics Страницы: 60

Бренд: Technics Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды