Yealink VC110 Скачать руководство пользователя страница 150

Страница: 150 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

138

Select the desired value from the pull-down list of Ringback Timeout(30-240).

Click Confirm to accept the change.

Auto refuse timeout defines a specific period of time within which the video
conferencing endpoint will stop ringing if the call is not answered.

The auto refuse timeout parameters on the endpoint are described below:

Parameter

Description

Configuration Method

Auto Refuse

Timeout

(30-240)

Configures the duration time (in
seconds) in the ringing state.

Default: 120

If it is set to 120, the endpoint will
stop ringing if the call is not
answered within 120s.

Web User Interface

To configure auto refuse timeout via web user interface:

Click on Setting->Call Features.

Содержание VC110













































































































































































































































































Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды

Yealink VC110, Руководство администратора

Результаты поиска

Содержание VC110

Отзывы:

Похожие инструкции для VC110

Бренды по названию

Популярные бренды