YASKAWA MP2100 Series Скачать руководство пользователя страница 219 | Manualshive

Страница: 219 / 455

background image

8 Motion Commands

8-10

8.3 External Positioning (EX_POSING)

The EX_POSING command positions the axis to the target position using the specified target position and speed.
Parameters related to acceleration and deceleration are set in advance.
If the external positioning signal turns ON during axis movement, the axis will move the distance specified for
the External Positioning Move Distance from the point at which the external positioning signal turned ON, and
then stop. If the external positioning signal does not turn ON, positioning will be completed to the original target
position.

(1) Operating Procedure

* If the Position Reference Type (OB

095) is set for an absolute mode, the target position can be set

before executing the command.

No.

Execution Conditions

Confirmation Method

1

There are no alarms.

Both IL

02 and IL

04 are 0.

2

The Servo ON condition.

IB

001 is ON.

3

Motion command execution has been completed.

IW

08 is 0 and IB

090 is OFF.

Set the motion setting parameters.

• External Positioning Move Distance:

OL

46

• External Positioning Signal: OW

04

• Positioning Speed: OL

10

• Acceleration/Deceleration Filter Type:

OW

03

• Speed Loop P/PI Switch: OW

01

• The target position can be changed while the axis is moving.
• The target position cannot be changed after the external

positioning signal is input.

• The positioning speed can be changed while the axis is moving.
• An override of between 0% to 327.67% can be set for the position-

ing speed.

• Set OB

090 to 1 to hold the command.

• Set OB

091 to 1 or execute the NOP motion command to abort

the command.

• A latch zone can be set as long as it is supported by the

SERVOPACK being used.

Execute the External Positioning
(EX_POSING) motion command.

• Set OW

08 to 2.

Set the target position.

• Target Position Setting: OL

1C

∗

Positioning starts.

• IW

08 will be 2 during positioning.

Turn ON the external positioning signal. The
axis will be moved the External Positioning
Move Distance and decelerate to a stop.

Positioning completed.

• IB

098 will turn ON.

Execute NOP motion command.

• Set OW

08 to 0.

Speed

%

100%

0

Time

t

Positioning
speed

Linear

acceleration time

Linear deceleration time

Rated speed

Latch signal

(external positioning signal)

External positioning
move distance

«
...
217
218
219
220
221
...
»

Содержание MP2100 Series








































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MP2100 Series

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

OneFlow OFTWH-R

Бренд: Watts Страницы: 8

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Coris Страницы: 4

MS6-SV-...-D-10V24

Бренд: Festool Страницы: 32

Бренд: SOMFY Страницы: 56

Бренд: Texas Instruments Страницы: 27

Бренд: IBM Страницы: 214

Бренд: STIEBEL ELTRON Страницы: 44

Бренд: Multi-Clean Страницы: 4

Бренд: Primo Water Страницы: 10

Бренд: PENGWYN Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды