YASKAWA GA800 Series, Техническое обслуживание и устранение неисправностей

Страница: 520 / 566

7.6 Drive Specifications
520 YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
Item Specification
Overvoltage
Protection
200 V Class: Stops when the DC bus voltage is more than approximately 410 V
400 V Class: Stops when the DC bus voltage is more than approximately 820 V
Undervoltage
Protection
200 V Class: Stops when the DC bus voltage decreases to less than approximately 190 V
400 V Class: Stops when the DC bus voltage decreases to less than approximately 380 V
Momentary Power
Loss Ride-thru
Stops when power loss is longer than 15 ms.
Continues operation if power loss is shorter than 2 s (depending on parameter settings).
Note:
• Stop time may be shortened depending on the load and motor speed.
• Drive capacity will change the continuous operation time. A Momentary Power Loss Recovery Unit is necessary to continue operation through a 2 s
power loss on models 2004 to 2056 and 4002 to 4031.
Heatsink Overheat
Protection
The drive stops when the thermistor detects an IGBT temperature more than approximately 100 °C (212 °F). The trip temperature level is different for different
drive models.
Braking Resistor
Overheat Protection
Overheat detection for braking resistor (optional ERF-type, 3% ED)
Stall Prevention
Stall prevention is available during acceleration, deceleration, and during run.
Ground Fault
Protection
Electronic circuit protection
Note:
This protection detects ground faults during run. The drive will not provide protection when:
•
There is a low-resistance ground fault for the motor cable or terminal block
• Energizing the drive when there is a ground fault.
DC Bus Charge LED
Charge LED illuminates when DC bus voltage is more than 50 V.
Braking Transistor
Models 2004 to 2138 and 4002 to 4168 have a braking transistor.
DC Link Choke
Models 2110 to 2415 and 4060 to 4720 have a DC link choke.
Table 7.13 Environment
Item
Specification
Area of Use Indoors
Power Supply
Overvoltage Category III
Permitted frequency fluctuation: ±5%
Permitted voltage fluctuation: -15% to +10%
200 V Class:
• Three-phase AC power supply 200 V to 240 V at 50/60 Hz
• DC power supply 270 V to 340 V
400 V Class:
• Three-phase AC power supply 380 V to 480 V at 50/60 Hz
• DC power supply 513 V to 679 V
6-Phase/12-Pulse 400 V Class:
• Three-phase AC power supply 380 V to 480 V at 50/60 Hz
Ambient Temperature
Setting
IP00/UL Open Type: -10 °C to +50 °C (14 °F to 122 °F)
IP20/UL Open Type/Heatsink External Mounting: -10 °C to +50 °C (14 °F to 122 °F)
IP20/UL Type 1: -10 °C to +40 °C (14 °F to 104 °F)
IP55/UL Type 12 Heatsink External Mounting; front side: -10 °C to +50 °C (14 °F to 122 °F)
IP55/UL Type 12 Heatsink External Mounting; back side: -10 °C to +40 °C (14 °F to 104 °F)
•
When you install the drive in an enclosure, use a cooling fan or air conditioner to keep the internal air temperature in the permitted range.
•
Do not let the drive freeze.
•
You can use IP00/IP20/UL Open Type drives at a maximum of 60 °C (140 °F) when you derate the output current.
•
You can use IP20/UL Type 1 drives at a maximum of 50 °C (122 °F) when you derate the output current.
Humidity
95% RH or less
Do not let condensation form on the drive.
Storage Temperature
-20 °C to +70 °C (-4 °F to +158 °F) (short-term temperature during transportation)
Surrounding Area
Pollution degree 2 or less
Install the drive in an area without:
• Oil mist, corrosive or flammable gas, or dust
• Metal powder, oil, water, or other unwanted materials
• Radioactive materials or flammable materials, including wood
•
Harmful gas or fluids
• Salt
• Direct sunlight