YASKAWA GA800 Series, Техническое обслуживание и устранение неисправностей, Страница: 171 / 566

Parameter
List
3
3.6 C: Tuning
YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting 171
No.
(Hex.)
Name Description
Default
(Range)
C5-24
(0359)
RUN
Motor 2 ASR Integral Time
2
Sets the ASR integral time for motor 2.
Determined by E3-01
(0.000 - 60.000 s)
C5-25
(035A)
Motor 2 ASR Limit
Set the motor 2 ASR output limit as a percentage of E1-04 [Maximum Output Frequency] .
5.0%
(0.0 - 20.0%)
C5-26
(035B)
Motor 2 ASR Delay Time
Sets the motor 2 filter time constant of the torque reference output from the speed loop. Usually it is
not necessary to change this setting.
Determined by E3-01
(0.000 - 0.500 s)
C5-27
(035C)
Motor 2 ASR Gain
Switchover Freq
Sets the frequency where the drive will switch between these parameters:
C5-21 and C5-23 [Motor 2 ASR Proportional Gain 1/2]
C5-22 and C5-24 [Motor 2 ASR Integral Time 1/2]
0.0
(0.0 - 400.0)
C5-28
(035D)
Motor 2 ASR Integral Limit
Set the upper limit of the motor 2 ASR integral amount as a percentage of the rated load.
400%
(0 - 400%)
C5-29
(0B18)
Expert
Speed Control Response
Sets the level of speed control responsiveness. Usually it is not necessary to change this setting.
0 : Standard
1 : High Performance 1
0
(0, 1)
C5-32
(0361)
Motor 2 Integral Oper at
Acc/Dec
Sets ASR integral operation during acceleration and deceleration for motor 2.
0 : Disabled
1 : Enabled
0
(0, 1)
C5-37
(0278)
Expert
Motor 2 Inertia
Sets the motor inertia for motor 2.
Note:
The display units for the default setting and setting range are different for different models:
• 0.0001 kgm 2 units (setting range: 0.0001 kgm 2 to 6.0000 kgm 2 ): 2004 to 2021, 4002 to 4012
•
0.001 kgm 2 units (setting range: 0.001 kgm 2 to 60.000 kgm 2 ): 2030 to 2211, 4018 to 4103,
T103
• 0.01 kgm 2 units (setting range: 0.01 kgm 2 to 600.00 kgm 2 ): 2257 to 2415, 4140 to 4720, T140
to T720
Determined by o2-04, C6-01
(0.0001 - 600.00 kgm 2 )
C5-38
(0279)
Expert
Motor 2 Load Inertia Ratio
Sets the load inertia ratio for the motor 2 inertia.
1.0
(0.0 - 6000.0)
C5-39
(030D)
ASR Primary Delay Time
Const 2
Sets the filter time constant used when the torque reference is output from ASR. Usually it is not
necessary to change this parameter.
0.000 s
(0.000 - 0.500 s)
C5-50
(0B14)
Expert
Notch Filter Frequency
Sets the machine resonance frequency.
Note:
Set C5-50 = 0 [0 Hz] to disable the notch filter.
0 Hz
(0, or 2 to 100 Hz)
C5-51
(0B15)
Expert
Notch Filter Bandwidth
Sets the notch width of the notch filter.
Note:
Set C5-50 = 0 [Notch Filter Frequency = 0 Hz] to disable the notch filter.
1.0
(0.5 - 5.0)
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV