Yamaha YZFR1W 2007 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 429

background image

FEATURES

1-10

Air intake temperature display

The air intake temperature display indicates
the temperature of the air drawn into the air fil-
ter case. Push the “RESET” button to switch
the coolant temperature display to the air
intake temperature display.

NOTE:

• Even if the air intake temperature is set to be

displayed, the coolant temperature warning
light comes on when the engine overheats.

• When the key is turned to “ON”, the coolant

temperature is automatically displayed, even
if the air intake temperature was displayed
prior to turning the key to “OFF”.

• When the air intake temperature display is

selected, “A” is displayed before the temper-
ature.

Self-diagnosis device

This model is equipped with a self-diagnosis
device for various electrical circuits.
If any of those circuits are defective, the engine
trouble warning light will come on, and then the
display will indicate a two-digit error code.
This model is also equipped with a self-diagno-
sis device for the immobilizer system.

If any of the immobilizer system circuits are
defective, the immobilizer system indicator
light will flash, and then the display will indicate
a two-digit error code.

NOTE:

If the display indicates error code 52, this could
be caused by transponder interference. If this
error code appears, try the following.

1. Use the code re-registering key to start the

engine.

NOTE:

Make sure there are no other immobilizer keys
close to the main switch, and do not keep more
than one immobilizer key on the same key ring!
Immobilizer system keys may cause signal
interference, which may prevent the engine
from starting

2. If the engine starts, turn it off and try start-

ing the engine with the standard keys.

3. If one or both of the standard keys do not

start the engine, take the vehicle, the code
re-registering key and both standard keys
to a Yamaha dealer and have the standard
keys re-registered.

If the display indicates any error codes, note
the code number, and then have a Yamaha
dealer check the vehicle.

CAUTION:

ECA4C81019

If the display indicates an error code, the
vehicle should be checked as soon as pos-
sible in order to avoid engine damage.

Display brightness and shift timing indica-
tor light control mode

1. Air intake temperature display

1. Error code display

1. Display brightness
2. Shift timing indicator light activation/deacti-

vation

3. Shift timing indicator light
4. Brightness level

«
...
14
15
16
17
18
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: LAZER Страницы: 13

Бренд: BMW Страницы: 245

Бренд: APRILIA Страницы: 9

Бренд: Sym Страницы: 31

Бренд: Honda Страницы: 3

Бренд: Suzuki Страницы: 26

Бренд: KTM Страницы: 36

Бренд: Honda Страницы: 127

Бренд: PIAGGIO Страницы: 8

Бренд: Fuelpak Страницы: 2

TERMOSCUD R224X

Бренд: tucanourbano Страницы: 4

Elefant 650 USA

Бренд: Cagiva Страницы: 136

Бренд: X-lite Страницы: 57

Бренд: Petzl Страницы: 14

Бренд: Beta Страницы: 5

Бренд: Abus Страницы: 6

: 6519512 00 22-01-40

Бренд: hepco & becker Страницы: 9

Бренд: KTM Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды