Yamaha YZFR1W 2007 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 429

background image

FEATURES

1-2

EAS20170

FEATURES

OUTLINE OF THE FI SYSTEM

The main function of a fuel supply system is to provide fuel to the combustion chamber at the opti-
mum air-fuel ratio in accordance with the engine operating conditions and the atmospheric tempera-
ture. In the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the
combustion chamber is created by the volume of the intake air and the fuel that is metered by the jet
used in the respective carburetor.
Despite the same volume of intake air, the fuel volume requirement varies by the engine operating
conditions, such as acceleration, deceleration, or operating under a heavy load. Carburetors that
meter the fuel through the use of jets have been provided with various auxiliary devices, so that an
optimum air-fuel ratio can be achieved to accommodate the constant changes in the operating con-
ditions of the engine.
As the requirements for the engine to deliver more performance and cleaner exhaust gases
increase, it becomes necessary to control the air-fuel ratio in a more precise and finely tuned man-
ner. To accommodate this need, this model has adopted an electronically controlled fuel injection
(FI) system, in place of the conventional carburetor system. This system can achieve an optimum
air-fuel ratio required by the engine at all times by using a microprocessor that regulates the fuel
injection volume according to the engine operating conditions detected by various sensors.
The adoption of the FI system has resulted in a highly precise fuel supply, improved engine
response, better fuel economy, and reduced exhaust emissions.

1. Intake air temperature sensor
2. Engine trouble warning light
3. Air induction system solenoid
4. Atmospheric pressure sensor
5. Throttle position sensor (for throttle cable

pulley)

6. Throttle servo motor
7. Throttle position sensor (for throttle valves)
8. Intake funnel servo motor
9. Injector
10.Intake air pressure sensor
11.Fuel pump
12.Lean angle sensor
13.ECU (engine control unit)

14.Starting circuit cut-off relay
15.Speed sensor
16.EXUP servo motor
17.O

2

sensor

18.Crankshaft position sensor
19.Coolant temperature sensor
20.Spark plug
21.Ignition coil
22.Cylinder identification sensor

«
...
6
7
8
9
10
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

Бренд: GAS GAS Страницы: 142

PowerCom INNOVA Plus Business

Бренд: AKE Страницы: 2

Бренд: Crivit Страницы: 50

Бренд: KC Страницы: 32

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 96

X-MAX 400 ABS 2018

Бренд: Yamaha Страницы: 118

Virago XV250T 2004

Бренд: Yamaha Страницы: 95

Бренд: Yamaha Страницы: 103

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды