Yamaha YZFR1W 2007 Скачать руководство пользователя страница 407 | Manualshive

Страница: 407 / 429

background image

ELECTRICAL COMPONENTS

8-88

c. Make sure that the current is higher than

the standard charging current written on
the battery.

NOTE:

If the current is lower than the standard charg-
ing current written on the battery, This type of
battery charger cannot charge the MF battery.
A variable voltage charger is recommended.

d. Charge the battery until the battery’s charg-

ing voltage is 15 V.

NOTE:

Set the charging time at 20 hours (maximum).

e. Measure the battery open-circuit voltage

after leaving the battery unused for more
than 30 minutes.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

6. Install:

• Battery

7. Connect:

• Battery leads

(to the battery terminals)

CAUTION:

ECA13630

First, connect the positive battery lead “1”,
and then the negative battery lead “2”.

8. Check:

• Battery terminals

Dirt

→

Clean with a wire brush.

Loose connection

→

Connect properly.

9. Lubricate:

• Battery terminals

10. Install:

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

EAS28040

CHECKING THE RELAYS

Check each switch for continuity with the
pocket tester. If the continuity reading is incor-
rect, replace the relay.

1. Disconnect the relay from the wire harness.
2. Connect the pocket tester (

Ω

×

1) and bat-

tery (12 V) to the relay terminal as shown.
Check the relay operation.
Out of specification

→

Replace.

Relay unit (starting circuit cut-off relay)

12.8 V or more --- Charging is complete.
12.7 V or less --- Recharging is required.
Under 12.0 V --- Replace the battery.

Recommended lubricant

Dielectric grease

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe

Relay operation

Continuity/No continuity

(between “3” to “4”)

1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe

Result

Continuity/No continuity

«
...
405
406
407
408
409
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: Maico Страницы: 13

Бренд: hepco & becker Страницы: 6

Бренд: Mallory Страницы: 3

Бренд: TM Страницы: 80

Бренд: LSL Страницы: 4

Бренд: Shad Страницы: 2

Бренд: Can-Am Страницы: 172

RT125D - PARTS CATALOGUE

Бренд: HYOSUNG Страницы: 73

Бренд: Benelli Страницы: 47

Tornado Naked Tre 1130

Бренд: Benelli Страницы: 55

sprite-barracuda

Бренд: Benelli Страницы: 64

Бренд: Petzl Страницы: 19

2011 Evo 4T 250

Бренд: Beta Страницы: 38

Бренд: Honda Страницы: 206

Бренд: hepco & becker Страницы: 2

Бренд: X-lite Страницы: 52

Бренд: 6KU Страницы: 17

Бренд: R&G Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды