Yamaha YZFR1W 2007 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 429

background image

EAS20070

NOTICE

This manual was produced by the Yamaha Motor Company, Ltd. primarily for use by Yamaha deal-
ers and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one
manual. Therefore, anyone who uses this book to perform maintenance and repairs on Yamaha
vehicles should have a basic understanding of mechanics and the techniques to repair these types
of vehicles. Repair and maintenance work attempted by anyone without this knowledge is likely to
render the vehicle unsafe and unfit for use.
This model has been designed and manufactured to perform within certain specifications in regard
to performance and emissions. Proper service with the correct tools is necessary to ensure that the
vehicle will operate as designed. If there is any question about a service procedure, it is imperative
that you contact a Yamaha dealer for any service information changes that apply to this model. This
policy is intended to provide the customer with the most satisfaction from his vehicle and to conform
to federal environmental quality objectives.
Yamaha Motor Company, Ltd. is continually striving to improve all of its models. Modifications and
significant changes in specifications or procedures will be forwarded to all authorized Yamaha deal-
ers and will appear in future editions of this manual where applicable.

NOTE:

• This Service Manual contains information regarding periodic maintenance to the emission control

system. Please read this material carefully.

• Designs and specifications are subject to change without notice.

EAS20080

IMPORTANT MANUAL INFORMATION

Particularly important information is distinguished in this manual by the following.

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!

Failure to follow WARNING instructions could result in severe injury or death to
the vehicle operator, a bystander or a person checking or repairing the vehicle.

A CAUTION indicates special precautions that must be taken to avoid damage
to the vehicle.

A NOTE provides key information to make procedures easier or clearer.

WARNING

CAUTION:

NOTE:

«
1
2
3
4
5
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: Honda Страницы: 393

STEADYSTAND Cross Basic

Бренд: ACEBIKES Страницы: 6

Бренд: Suzuki Страницы: 26

640 LC4 Adventure

Бренд: KTM Страницы: 59

Бренд: hepco & becker Страницы: 2

Montana 7 Series

Бренд: Garmin Страницы: 24

Бренд: DYNATEK Страницы: 4

Бренд: Aim Страницы: 5

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 84

Бренд: GÜDE Страницы: 80

Бренд: GÜDE Страницы: 88

Бренд: Shift Power Страницы: 7

Бренд: Shift Power Страницы: 7

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды