Yamaha YZFR1W 2007 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 429

background image

CHASSIS

3-27

NOTE:

To maintain the proper wheel alignment, adjust
both sides evenly.

d. Tighten both locknuts to specification.

e. Tighten the wheel axle nut to specification.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21440

LUBRICATING THE DRIVE CHAIN

The drive chain consists of many interacting
parts. If the drive chain is not maintained prop-
erly, it will wear out quickly. Therefore, the drive
chain should be serviced, especially when the
vehicle is used in dusty areas.
This vehicle has a drive chain with small rub-
ber O-rings between each side plate. Steam
cleaning, high-pressure washing, certain sol-
vents, and the use of a coarse brush can dam-
age these O-rings. Therefore, use only
kerosene to clean the drive chain. Wipe the
drive chain dry and thoroughly lubricate it with
engine oil or chain lubricant that is suitable for
O-ring chains. Do not use any other lubricants
on the drive chain since they may contain sol-
vents that could damage the O-rings.

EAS21500

CHECKING AND ADJUSTING THE STEER-
ING HEAD

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the front wheel is elevated.

2. Check:

• Steering head

Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding/looseness

→

Adjust the steering

head.

3. Remove:

• Upper bracket

Refer to "HANDLEBARS" on page 4-45
and "STEERING HEAD" on page 4-59.

4. Adjust:

• Steering head

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the lock washer “1”, the upper ring

nut “2”, and the rubber washer “3”.

b. Loosen the lower ring nut “4” and then

tighten it to specification with a steering nut
wrench “5”.

NOTE:

Set the torque wrench at a right angle to the
steering nut wrench.

Direction “a”

Drive chain is tightened.

Direction “b”

Drive chain is loosened.

Locknut

16 Nm (1.6 m·kg, 12 ft·lb)

Wheel axle nut

150 Nm (15 m·kg, 108 ft·lb)

Recommended lubricant

Engine oil or chain lubricant
suitable for O-ring chains

«
...
108
109
110
111
112
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: B-PWR Страницы: 13

Mesh Helmet Cover

Бренд: Ops-Core Страницы: 2

Бренд: Ducati Страницы: 123

Бренд: Memphis Shades Страницы: 2

Бренд: KTM Страницы: 38

Бренд: X-lite Страницы: 84

Бренд: MOTO GUZZI Страницы: 266

Бренд: Fantic Motor Страницы: 60

Бренд: UBCO Страницы: 27

SHERCO 50 SE 2022

Бренд: SHERCO Страницы: 226

Бренд: Shark Страницы: 44

Бренд: Malaguti Страницы: 383

Бренд: KTM Страницы: 20

Бренд: Shift Power Страницы: 7

Бренд: Shift Power Страницы: 7

Бренд: Dräger Страницы: 256

Бренд: Legend Страницы: 2

DUCATI HYPERCROSS

Бренд: Peg-Perego Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды