manualshive.com logo in svg

Yamaha YZFR1W 2007, Руководство по обслуживанию

Yamaha YZFR1W 2007 - мощный спортивный мотоцикл, идеальный для гонок и ежедневного использования. Вы можете бесплатно загрузить Руководство по обслуживанию на manualshive.com, чтобы поддерживать свой мотоцикл в отличной форме. Незаменимый инструмент для любого владельца этой модели!

Поделиться
Скачать
background image

HANDLEBARS

4-48

4. Install:

• Throttle grip
• Throttle cable housing “1”
• Throttle cables

NOTE:

Align the projection “a” on the throttle cable 
housing with the hole “b” in the right handlebar.

5. Install:

• Clutch lever holder “1”

NOTE:

Align the slit on the clutch lever holder with the 
punch mark “a” on the left handlebar.

6. Install:

• Left handlebar switch “1”

NOTE:

Align the projection “a” on the left handlebar 
switch with the hole “b” on the left handlebar.

7. Install:

• Handlebar grip

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Apply a thin coat of rubber adhesive onto 

the end of the left handlebar.

b. Slide the handlebar grip over the end of the 

left handlebar.

c. Wipe off any excess rubber adhesive with a 

clean rag.

WARNING

EWA13700

Do not touch the handlebar grip until the 
rubber adhesive has fully dried.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

8. Adjust:

• Clutch cable free play

Refer to "ADJUSTING THE CLUTCH 
CABLE FREE PLAY" on page 3-14.

9. Adjust:

• Throttle cable free play

Refer to "ADJUSTING THE THROTTLE 
CABLE FREE PLAY" on page 3-8.

EAS4C81004

CHECKING THE STEERING DAMPER

1. Check:

• Steering damper body

Damage/oil leaks 

→

 Replace.

(It replace with the assembly.)

• Steering damper rod

Bends/scratch 

→

 Replace.

(It replace with the assembly.)

• Bearing

Damage/pitting 

→

 Replace.

(It replace with the assembly.)

Clutch lever free play

10.0–15.0 mm (0.39–0.59 in)

Throttle cable free play

3.0–5.0 mm (0.12–0.20 in)

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

GAS GAS EX 450F 2021 Owner'S Manual preview
EX 450F 2021
Бренд: GAS GAS Страницы: 142
R&G CP0473 Fitting Instructions Manual preview
CP0473
Бренд: R&G Страницы: 14
hepco & becker 661329 01 01 Quick Start Manual preview
661329 01 01
Бренд: hepco & becker Страницы: 4
JIMS MILWAUKEE-EIGHT 5833 Instruction Sheet preview
MILWAUKEE-EIGHT 5833
Бренд: JIMS Страницы: 10
Memphis Shades 2321-0054 Mounting Instructions preview
2321-0054
Бренд: Memphis Shades Страницы: 2
APRILIA SCARABEO 100 4T - 06-2001 PART6 Manual preview
SCARABEO 100 4T - 06-2001 PART6
Бренд: APRILIA Страницы: 6
Blata Origami B1 Service Manual preview
Origami B1
Бренд: Blata Страницы: 17
Yamaha XS650SE Shop Manual preview
XS650SE
Бренд: Yamaha Страницы: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Бренд: Yamaha Страницы: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Бренд: Yamaha Страницы: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Бренд: Yamaha Страницы: 94
Malossi 5518095 Manual preview
5518095
Бренд: Malossi Страницы: 24
DYNATEK DDK1-11 Installation Manual preview
DDK1-11
Бренд: DYNATEK Страницы: 11
Sealey PWH699R Instructions preview
PWH699R
Бренд: Sealey Страницы: 4
Skully FENIX AR User Manual preview
FENIX AR
Бренд: Skully Страницы: 36
Beta RR 4T - 250 Workshop Manual preview
RR 4T - 250
Бренд: Beta Страницы: 196
Beta RR 390 Manual preview
RR 390
Бренд: Beta Страницы: 360
KTM 2015 200 Duke Owner'S Manual preview
2015 200 Duke
Бренд: KTM Страницы: 177

Бренды по названию

Популярные бренды

Загрузить еще бренды