Yamaha YZFR1W 2007 Скачать руководство пользователя страница 162

Страница: 162 / 429

REAR BRAKE

4-40

EAS22590

REMOVING THE REAR BRAKE CALIPER

NOTE:

Before disassembling the brake caliper, drain
the brake fluid from the entire brake system.

1. Remove:

• Union bolt “1”
• Copper washers “2”
• Brake hose “3”
• Brake caliper “4”

NOTE:

Put the end of the brake hose into a container
and pump out the brake fluid carefully.

EAS22600

DISASSEMBLING THE REAR BRAKE CALI-
PER

1. Remove:

• Brake caliper piston “1”
• Brake caliper piston seals “2”

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Secure the brake caliper piston with a

piece of wood “a”

b. Blow compressed air into the brake hose

joint opening “b” to force out the piston from
the brake caliper.

WARNING

EWA13550

• Cover the brake caliper piston with a rag.

Be careful not to get injured when the pis-
ton is expelled from the brake caliper.

• Never try to pry out the brake caliper pis-

ton.

c. Remove the brake caliper piston seals.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS22640

CHECKING THE REAR BRAKE CALIPER

1. Check:

• Brake caliper pistons “1”

Rust/scratches/wear

→

Replace the brake

caliper pistons.

• Brake caliper cylinders “2”

Scratches/wear

→

Replace the brake cali-

per assembly.

• Brake caliper body “3”

Cracks/damage

→

Replace the brake cali-

per assembly.

• Brake fluid delivery passages

(brake caliper body)
Obstruction

→

Blow out with compressed

air.

Recommended brake component
replacement schedule

Brake pads

If necessary

Piston seals

Every two years

Brake hoses

Every four years

Brake fluid

Every two years and
whenever the brake is
disassembled

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды