Yamaha YZFR1W 2007 Скачать руководство пользователя страница 134

Страница: 134 / 429

FRONT WHEEL

4-12

NOTE:

Start with the lightest weight.

b. Turn the front wheel 90

so that the heavy

spot is positioned as shown.

c. If the heavy spot does not stay in that posi-

tion, install a heavier weight.

d. Repeat steps (b) and (c) until the front

wheel is balanced.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Check:

• Front wheel static balance

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the front wheel and make sure it stays

at each position shown.

b. If the front wheel does not remain station-

ary at all of the positions, rebalance it.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS22000

INSTALLING THE FRONT WHEEL

The following procedure applies to both of the
brake discs.
1. Lubricate:

• Wheel axle
• Oil seal lips

2. Lift the wheel up between the fork legs.
3. Insert the wheel axle.

NOTE:

Install the tire and wheel with the mark “1”
pointing in the direction of wheel rotation.

4. Lower the front wheel so that it is on the

ground.

5. Tighten:

• Front wheel axle bolt

• Front wheel axle pinch bolt

CAUTION:

ECA4C81001

Before tightening the wheel axle, push
down hard on the handlebar(s) several
times and check if the front fork rebounds
smoothly.

6. Install:

• Front brake calipers

Recommended lubricant

Lithium-soap-based grease

Front wheel axle bolt

91 Nm (9.1 m·kg, 66 ft·lb)

Front wheel axle pinch bolt

21 Nm (2.1 m·kg, 15 ft·lb)

Front brake caliper bolt

35 Nm (3.5 m·kg, 25 ft·lb)

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды