Yamaha YZFR1W 2007 Скачать руководство пользователя страница 277

Страница: 277 / 429

CRANKSHAFT

5-77

EAS26190

INSTALLING THE CONNECTING ROD AND
PISTON

The following procedure applies to all of the
connecting rods and pistons.
1. Install:

• Top ring “1”
• 2nd ring “2”
• Oil ring expander “4”
• Upper oil ring rail “3”
• Lower oil ring rail “5”

NOTE:

Be sure to install the piston rings so that the
manufacturer’s marks or numbers “a” face up.

2. Install:

• Piston “1”

(onto the respective connecting rod “2”)

• Piston pin “3”

• Piston pin clip “4”

NOTE:

• Apply engine oil onto the piston pin.
• Make sure that the “Y” mark “a” on the con-

necting rod faces left when the arrow mark
“b” on the piston is pointing up as shown.

• Reinstall each piston into its original cylinder

(numbering order starting from the left: #1 to
#4).

3. Lubricate:

• Piston
• Piston rings
• Cylinder

(with the recommended lubricant)

4. Offset:

• Piston ring end gaps

5. Lubricate:

• Crankshaft pins
• Big end bearings
• Connecting rod big end inner surface

(with the recommended lubricant)

6. Check:

• Cylinder stud bolts “1”

New

Recommended lubricant

Engine oil

a. Top ring
b. Lower oil ring rail
c. Upper oil ring rail
d. 2nd ring
e. Oil ring expander

A. Exhaust side

Recommended lubricant

Engine oil

Cylinder stud bolt

8 Nm (0.8 m·kg, 5.8 ft·lb)

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды