Yamaha YZFR1W 2007 Скачать руководство пользователя страница 216

Страница: 216 / 429

CAMSHAFTS

5-16

CAUTION:

ECA4C81004

• Lubricate the camshaft cap bolts with the

engine oil.

• The camshaft cap bolts must be tightened

evenly or damage to the cylinder head,
camshaft caps, and camshafts will result.

• Do not turn the crankshaft when installing

the camshaft to avoid damage or
improper valve timing.

6. Tighten:

• Camshaft sprocket bolts “1”

CAUTION:

ECA4C81005

Be sure to tighten the camshaft sprocket
bolts to the specified torque to avoid the
possibility of the bolts coming loose and
damaging the engine.

7. Align:

• Camshaft punch mark “a”

Align the camshaft punch mark “a” and the
camshaft cap arrow mark “b”.

8. Install:

• Gasket
• Timing chain tensioner “1”
• Timing chain tensioner bolts “2”

CAUTION:

ECA4C81006

The arrow mark “a” on the timing chain ten-
sioner should face up.

WARNING

EWA4C81004

Always use a new gasket.

9. Turn:

• Crankshaft

(several turns clockwise)

10. Check:

• “T” mark “a”

Make sure the “T” mark on the pickup rotor
is aligned with the crankcase mating sur-
face “b”.

• Camshaft punch mark “c”

Make sure the punch mark “c” on the cam-
shaft is aligned with the camshaft cap
arrow mark “d”.
Out of alignment

→

Adjust.

Refer to the installation steps above.

Camshaft sprocket bolt

24 Nm (2.4 m·kg, 17 ft·lb)

Camshaft wrench

90890-04143
YM-04143

Camshaft wrench

90890-04143
YM-04143

Timing chain tensioner bolt

10 Nm (1.0 m·kg, 7.2 ft·lb)

New

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды