Yamaha YZFR1W 2007 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 429

background image

ENGINE

3-8

NOTE:

• If more than one throttle body has a bypass

air screw with a white paint mark, use the
one with the lowest vacuum pressure as the
standard.

• After each step, rev the engine two or three

times, each time for less than a second, and
check the synchronization again.

• If an air screw was removed, turn the screw

3/4 turn in and be sure to synchronize the
throttle body.

NOTE:

• The difference in vacuum pressure between

two throttle bodies should not exceed 1.33
kPa (10 mmHg).

• If you are unable to adjust the throttle body

synchronization using this procedure, use
the following procedure instead.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

Alternate procedure

NOTE:

Use this alternate procedure if you are unable
to adjust the throttle body synchronization
using the basic procedure.

a. Start the engine, warm it up for several

minutes, and then let it run at the specified
engine idling speed.

b. Turn all of the bypass air screws in fully.
c. Using the throttle body with the lowest vac-

uum pressure as the standard, turn out the
bypass air screws of the other throttle bod-
ies to adjust them.

NOTE:

• Do not turn out the bypass air screw of the

throttle body with the lowest vacuum pres-
sure.

• After each step, rev the engine two or three

times, each time for less than a second, and
check the synchronization again.

• If an air screw was removed, turn the screw

3/4 turn in and be sure to synchronize the
throttle body.

NOTE:

The difference in vacuum pressure between
two throttle bodies should not exceed 1.33 kPa
(10 mmHg).

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

9. Stop the engine and remove the measuring

equipment.

10. Adjust:

• Throttle cable free play

Refer to "ADJUSTING THE THROTTLE
CABLE FREE PLAY" on page 3-8.

11. Install:

• Fuel tank
• Fuel tank side cover

Refer to "FUEL TANK" on page 7-1.

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

EAS20630

ADJUSTING THE THROTTLE CABLE FREE
PLAY

NOTE:

Prior to adjusting the throttle cable free play,
the carburetor synchronization should be
adjusted properly.

1. Check:

• Throttle cable free play “a”

Out of specification

→

Adjust.

Intake vacuum

22.0 kPa (6.5 inHg) (165
mmHg)

Engine idling speed

1150–1250 r/min

Intake vacuum

22.0 kPa (6.5 inHg) (165
mmHg)

Throttle cable free play

3.0–5.0 mm (0.12–0.20 in)

«
...
89
90
91
92
93
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: Dayi Motor Страницы: 15

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

TwinSpark Super head plus R

Бренд: Takegawa Страницы: 5

Бренд: BMW Страницы: 416

Бренд: Crivit Страницы: 50

Бренд: Romet Страницы: 52

Бренд: Kabuto Страницы: 6

Бренд: HJC Страницы: 9

Бренд: hepco & becker Страницы: 2

Бренд: LSL Страницы: 4

BLITZ 9-13 Visor

Бренд: Fubag Страницы: 17

SENDA R/SM 125 4T Baja

Бренд: Derbi Страницы: 124

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 4

Spyder ST Limited SE5

Бренд: Can-Am Страницы: 41

Fast Time F-10 50cc

Бренд: Malaguti Страницы: 151

Бренд: HYOSUNG Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды