Yamaha YZFR1W 2007 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 429

background image

CHASSIS

3-34

WARNING

EWA14090

After extensive tests, the tires listed below
have been approved by Yamaha Motor Co.,
Ltd. for this model. The front and rear tires
should always be by the same manufac-
turer and of the same design. No guarantee
concerning handling characteristics can be
given if a tire combination other than one
approved by Yamaha is used on this vehi-
cle.

WARNING

EWA13210

New tires have a relatively low grip on the
road surface until they have been slightly
worn. Therefore, approximately 100 km
should be traveled at normal speed before
any high-speed riding is done.

NOTE:

For tires with a direction of rotation mark “1”:
• Install the tire with the mark pointing in the

direction of wheel rotation.

• Align the mark “2” with the valve installation

point.

EAS21670

CHECKING THE WHEELS

The following procedure applies to both of the
wheels.
1. Check:

• Wheel

Damage/out-of-round

→

Replace.

WARNING

EWA13260

Never attempt to make any repairs to the
wheel.

NOTE:

After a tire or wheel has been changed or
replaced, always balance the wheel.

EAS21690

CHECKING AND LUBRICATING THE
CABLES

The following procedure applies to all of the
inner and outer cables.

WARNING

EWA13270

Damaged outer cable may cause the cable
to corrode and interfere with its movement.
Replace damaged outer cable and inner
cables as soon as possible.

1. Check:

• Outer cable

Damage

→

Replace.

2. Check:

• Cable operation

Rough movement

→

Lubricate.

NOTE:

Hold the cable end upright and pour a few
drops of lubricant into the cable sheath or use
a suitable lubricating device.

EAS21700

LUBRICATING THE LEVERS

Lubricate the pivoting point and metal-to-metal
moving parts of the levers.

Front tire

Size

120/70 ZR17M/C (58W)

Manufacturer/model

PIRELLI/DIABLO CORSA E

Manufacturer/model

MICHELIN/Pilot POWER

Rear tire

Size

190/50 ZR17M/C (73W)

Manufacturer/model

PIRELLI/DIABLO CORSA L

Manufacturer/model

MICHELIN/Pilot POWER

Recommended lubricant

Engine oil or a suitable cable
lubricant

Recommended lubricant

Lithium-soap-based grease

«
...
115
116
117
118
119
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: KYMCO Страницы: 58

Бренд: Memphis Shades Страницы: 2

Бренд: KTM Страницы: 29

Бренд: hepco & becker Страницы: 6

Бренд: hepco & becker Страницы: 3

Бренд: EINHELL Страницы: 48

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 84

NMAX GPD155 2020

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 104

NEO'S ESS025 2022

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды