Yamaha YZFR1W 2007 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 429

background image

CHASSIS

3-29

e. Repeat the above procedure on the oppo-

site handlebar.

f.

If the steering head tension is out of specifi-
cation (both handlebars should be within
specification), remove the upper bracket
and loosen or tighten the upper ring nut.

g. Reinstall the upper bracket and measure

the steering head tension again as
described above.

h. Repeat the above procedure until the steer-

ing head tension is within specification.

i.

Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding/looseness

→

Adjust the steering

head.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS21530

CHECKING THE FRONT FORK

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there
is no danger of it falling over.

2. Check:

• Inner tube “1”

Damage/scratches

→

Replace.

• Oil seal “2”

Oil leakage

→

Replace.

3. Hold the vehicle upright and apply the front

brake.

4. Check:

• Front fork operation

Push down hard on the handlebar several
times and check if the front fork rebounds
smoothly.
Rough movement

→

Repair.

Refer to "FRONT FORK" on page 4-50.

EAS21580

ADJUSTING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.

WARNING

EWA13150

• Always adjust both front fork legs evenly.

Uneven adjustment can result in poor
handling and loss of stability.

• Securely support the vehicle so that there

is no danger of it falling over.

Spring preload

CAUTION:

ECA13570

• Grooves are provided to indicate the

adjustment position.

• Never go beyond the maximum or mini-

mum adjustment positions.

1. Adjust:

• Spring preload

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the adjusting bolt “1” in direction “a” or

“b”.

Direction “a”

Spring preload is increased (suspension
is harder).

Direction “b”

Spring preload is decreased (suspension
is softer).

«
...
110
111
112
113
114
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: Qlink Страницы: 44

Бренд: Graphite Страницы: 44

Бренд: hepco & becker Страницы: 5

Бренд: hepco & becker Страницы: 2

Бренд: KTM Страницы: 163

Бренд: Cobra Страницы: 38

TwinSpark Super head plus R

Бренд: Takegawa Страницы: 5

Бренд: BMW Страницы: 416

Бренд: Suzuki Страницы: 26

Бренд: OKBABY Страницы: 35

Бренд: Artotic Страницы: 9

Бренд: Crivit Страницы: 58

Бренд: Wolfman Страницы: 3

Бренд: AGV Страницы: 64

Бренд: hepco & becker Страницы: 3

Бренд: probrake Страницы: 2

Бренд: probrake Страницы: 2

Бренд: KTM Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды