Yamaha YZFR1W 2007 Скачать руководство пользователя страница 350 | Manualshive

Страница: 350 / 429

background image

FUEL INJECTION SYSTEM

8-31

EAS27350

ECU SELF-DIAGNOSTIC FUNCTION

The ECU is equipped with a self-diagnostic function in order to ensure that the fuel injection system
is operating normally. If this function detects a malfunction in the system, it immediately operates the
engine under substitute characteristics and illuminates the engine trouble warning light to alert the
rider that a malfunction has occurred in the system. Once a malfunction has been detected, a fault
code is stored in the memory of the ECU.
• To inform the rider that the fuel injection system is not functioning, the engine trouble warning light

flashes when the start switch is being pushed to start the engine.

• If a malfunction is detected in the system by the self-diagnostic function, the ECU provides an

appropriate substitute characteristic operation, and alerts the rider of the detected malfunction by
illuminating the engine trouble warning light.

• After the engine has been stopped, the lowest fault code number appears on the odometer/trip

meter/fuel reservoir trip meter/stop watch LCD. Once a fault code has been displayed, it remains
stored in the memory of the ECU until it is deleted.

Engine trouble warning light indication and FI system operation

* The warning light flashes when any one of the conditions listed below is present and the start

switch is pushed:

Checking engine trouble warning light

The engine trouble warning light comes on for 1.4 seconds after the main switch has been turned to
“ON” and it comes on while the start switch is being pushed. If the warning light does not come on
under these conditions, the warning light (LED) may be defective.

Warning light indica-
tion

ECU operation

FI operation

Vehicle operation

Flashing*

Warning provided
when unable to start
engine

Operation stopped

Cannot be operated

Remains on

Malfunction detected

Operated with substi-
tute characteristics in
accordance with the
description of the mal-
function

Can or cannot be oper-
ated depending on the
fault code

11:

Cylinder identification sensor

30:

Lean angle sensor
(latch up detected)

12:

Crankshaft position sensor

41:

Lean angle sensor
(open or short-circuit)

19:

Sidestand switch
(open circuit in the wire to the ECU)

50:

ECU internal malfunction
(faulty ECU memory)

a

b

c

c

d

«
...
348
349
350
351
352
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: TREND Страницы: 38

MULTISTRADA 1200S

Бренд: Ducati Страницы: 311

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 360

Бренд: Yamaha Страницы: 580

Бренд: Yamaha Страницы: 98

Бренд: Custom Dynamics Страницы: 2

Бренд: Royal Enfield Страницы: 234

Бренд: DYNATEK Страницы: 8

Бренд: Aim Страницы: 5

Бренд: hepco & becker Страницы: 2

Бренд: Scott Страницы: 22

Бренд: SCORPION Страницы: 2

Бренд: SCORPION Страницы: 15

LEDV46-T-TS LIGHT KIT

Бренд: AdMore Lighting Страницы: 4

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды