Yamaha YZFR1W 2007 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 429

background image

ENGINE

3-15

4. Install:

• Air filter element

NOTE:

Install a new air filter element by fitting the pro-
jections 1 on the element into the slots in the
air filter case.

CAUTION:

ECA4C81021

• Make sure that the air filter element is

properly seated in the air filter case.

• Pay attention to handling of the products

so that the projections is not deformed.

5. Install:

• Air filter case cover

CAUTION:

ECA4C81015

Never operate the engine without the air fil-
ter element installed. Unfiltered air will
cause rapid wear of engine parts and may
damage the engine. Operating the engine
without the air filter element will also affect
throttle bodies synchronization, leading to
poor engine performance and possible
overheating.

NOTE:

When installing the air filter element into the air
filter case cover, make sure that the sealing
surfaces are aligned to prevent any air leaks.

6. Install:

• Fuel tank
• Fuel tank side covers

Refer to "FUEL TANK" on page 7-1.

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

EAS21010

CHECKING THE THROTTLE BODY JOINTS

The following procedure applies to all of the
throttle body joints and intake manifolds.
1. Remove:

• Throttle bodies

Refer to "THROTTLE BODIES" on page 7-
4.

2. Check:

• Throttle body joints “1”

Cracks/damage

→

Replace.

3. Install:

• Throttle bodies

Refer to "THROTTLE BODIES" on page 7-
4.

EAS21030

CHECKING THE FUEL LINE

The following procedure applies to all of the
fuel, vacuum and breather hoses.
1. Remove:

• Rider seat

Refer to "GENERAL CHASSIS" on page 4-
1.

• Fuel tank side covers
• Fuel tank

Refer to "FUEL TANK" on page 7-1.

2. Check:

• Fuel hose “1”
• Breather hose “2”

Cracks/damage

→

Replace.

Loose connection

→

Connect properly.

1. Projection 1
2. Projection 2
3. Slot

«
...
96
97
98
99
100
...
»

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

Бренд: Yamaha Страницы: 650

Бренд: Öhlins Страницы: 8

Бренд: WangYe Страницы: 19

Бренд: Yoshimura Страницы: 4

Бренд: hepco & becker Страницы: 5

TXT ROOKIE - 2006

Бренд: GAS GAS Страницы: 32

Бренд: dushi Страницы: 4

Бренд: Pagsta Страницы: 47

Бренд: VESPA Страницы: 25

Бренд: Innovv Страницы: 2

Бренд: Baotian Страницы: 30

Бренд: N-Com Страницы: 36

Бренд: Artago Страницы: 4

Drystash Series

Бренд: Oxford Страницы: 20

Heritage Series

Бренд: Oxford Страницы: 28

Бренд: B-PWR Страницы: 11

Бренд: X-lite Страницы: 80

Бренд: KTM Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды