Yamaha YZFR1W 2007 Скачать руководство пользователя страница 153

Страница: 153 / 429

FRONT BRAKE

4-31

EAS22520

ASSEMBLING THE FRONT BRAKE MAS-
TER CYLINDER

WARNING

EWA13520

• Before installation, all internal brake com-

ponents should be cleaned and lubricated
with clean or new brake fluid.

• Never use solvents on internal brake

components.

1. Instal:

• Brake master cylinder kit

EAS22540

INSTALLING THE FRONT BRAKE MASTER
CYLINDER

1. Install:

• Brake master cylinder “1”
• Brake master cylinder holder “2”

NOTE:

• Install the brake master cylinder holder with

the “UP” mark “a” facing up.

• Align the end of the brake master cylinder

holder with the punch mark “b” on the han-
dlebar.

• First, tighten the upper bolt, then the lower

bolt.

• There should be 2–2.5 mm (0.08–0.10 in) of

clearance between the right handlebar
switch and the brake master cylinder holder.

2. Install:

• Copper washers
• Brake hose
• Union bolt

WARNING

EWA13530

Proper brake hose routing is essential to
insure safe vehicle operation. Refer to
"CABLE ROUTING" on page 2-39.

NOTE:

• While holding the brake hose, tighten the

union bolt as shown.

• Turn the handlebar to the left and right to

make sure the brake hose does not touch
other parts (e.g., wire harness, cables,
leads). Correct if necessary.

3. Fill:

• Brake fluid reservoir

(with the specified amount of the recom-
mended brake fluid)

Recommended fluid

DOT 4

Front brake master cylinder
holder bolt

13 Nm (1.3 m·kg, 9.4 ft·lb)

New

Front brake hose union bolt

30 Nm (3.0 m·kg, 22 ft·lb)

a. 36

b. 3 mm (0.12 in)

Recommended fluid

DOT 4

New

Содержание YZFR1W 2007














































































































































































































































































































































































































































Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды

Yamaha YZFR1W 2007, Руководство по обслуживанию

Результаты поиска

Содержание YZFR1W 2007

Отзывы:

Похожие инструкции для YZFR1W 2007

Бренды по названию

Популярные бренды