manualshive.com logo in svg

Yamaha YZFR1W 2007, Руководство по обслуживанию

Yamaha YZFR1W 2007 - мощный спортивный мотоцикл, идеальный для гонок и ежедневного использования. Вы можете бесплатно загрузить Руководство по обслуживанию на manualshive.com, чтобы поддерживать свой мотоцикл в отличной форме. Незаменимый инструмент для любого владельца этой модели!

Поделиться
Скачать
background image

IMMOBILIZER SYSTEM

8-74

Voiding the standard key code:

If a standard key has been lost, it is possible to disable its use by re-registering the remaining stan-
dard key. Standard key registration erases the stored standard key code from the memory, thus dis-
abling the lost standard key.To re-register, refer to “Standard key registration”.

Standard key code voiding method

EAS27701

TROUBLESHOOTING

When the main switch is turned to “ON”, the immobilizer system indicator light does not come on nor 
flashes.

NG

→

OK

↓

NG

→

OK

↓

NG

→

OK

↓

a. Main switch “ON”
b. Main switch “OFF”
c. LED on
d. LED off
e. Less than 5.0 s
f. Code re-registering key

g. Remaining standard key
h. Registration mode

A. If the immobilizer system indicator light 

stops flashing 5 seconds after the first stan-
dard key is registered, the second standard 
key cannot be registered.

1 Check the fuses.

(Main, ignition and backup)
Refer to "CHECKING THE FUSES" 
on page 8-85.

Replace the fuse(s).

2 Check the battery.

Refer to "CHECKING AND 
CHARGING THE BATTERY" on 
page 8-85.

• Clean the battery terminals.
• Recharge or replace the battery.

3 Check the main switch.

Refer to "CHECKING THE 
SWITCHES" on page 8-81.

Replace the main switch/immobilizer 
unit.

Содержание YZFR1W 2007














































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZFR1W 2007

GAS GAS TXTPRO - 2009 Manual preview
TXTPRO - 2009
Бренд: GAS GAS Страницы: 57
X-lite X-803RS Safety And Instructions For Use preview
X-803RS
Бренд: X-lite Страницы: 136
SUOMY C1SF0001 Instructions For User preview
C1SF0001
Бренд: SUOMY Страницы: 84
Suzuki 990D0-44G00-ALM Fitting Instructions Manual preview
990D0-44G00-ALM
Бренд: Suzuki Страницы: 24
DYNATEK DDK2-8 Installation & User Manual preview
DDK2-8
Бренд: DYNATEK Страницы: 11
hepco & becker 6264538 00 01 Mounting Instructions preview
6264538 00 01
Бренд: hepco & becker Страницы: 3
Fast H-NAPE CHINSTRAP Operator'S Manual preview
H-NAPE CHINSTRAP
Бренд: Fast Страницы: 24
R&G PKS0119 Fitting Instructions Manual preview
PKS0119
Бренд: R&G Страницы: 6
R&G RAD0253 Series Fitting Instructions Manual preview
RAD0253 Series
Бренд: R&G Страницы: 12
Fuelpak SOFTAIL 2012 Instructions preview
SOFTAIL 2012
Бренд: Fuelpak Страницы: 2
Klarfit 10030853 Quick Start Manual preview
10030853
Бренд: Klarfit Страницы: 8
MZ 125 SM Repair Manual preview
125 SM
Бренд: MZ Страницы: 204
Yamaha FreeGo LTK125 2019 Owner'S Manual preview
FreeGo LTK125 2019
Бренд: Yamaha Страницы: 84
Yamaha FZ-07 Owner'S Manual preview
FZ-07
Бренд: Yamaha Страницы: 106
Yamaha FJR13AY(C) Owner'S Manual preview
FJR13AY(C)
Бренд: Yamaha Страницы: 114
Yamaha FJR13AEY Owner'S Manual preview
FJR13AEY
Бренд: Yamaha Страницы: 112
Yamaha FJR13ESE(C) Owner'S Manual preview
FJR13ESE(C)
Бренд: Yamaha Страницы: 132
Yamaha FJR13AF 2014 Owner'S Manual preview
FJR13AF 2014
Бренд: Yamaha Страницы: 130

Бренды по названию

Популярные бренды

Загрузить еще бренды